Home > Products > Bushings > QD Bushings >

Martin Catalog QD Bushing SH

Martin Catalog QD Bushing SH

Martin Catalog QD Bushing SH
Martin Catalog QD Bushing SHMartin Catalog QD Bushing SHMartin Catalog QD Bushing SH
CategoriesQD Bushings
AlbumView larger image
ModelMartin Catalog QD Bushing SH series bushings
ProductQD SH
Materialsteel C45
CatalogMartin
Bore typeStandard
Bolt Circle2.25
Surface TreatmentBlackoxided
FOB portShanghai/Ningbo
Terms of PaymentL/C, D/P, Western Union
Update Time2019-12-20
Detail Information
Martin Catalog QD Bushing SH series bushings
Martin Catalog QD Bushing SH series bushings
The taper-bored “QD” sprocket easily fits over the tapered hub and tightening of the cap screws produces a tight press fit on the shaft. The sprocket part is easily removed from the hub by using the pull-up bolts as jack screws in the holes tapped in the rim of the sprocket.

Zhijiang Sprocket factory?has been making all kinds of Martin Catalog QD Bushing and sprockets for American customers more than 20years, material including steel C1045, SUS304, Casting.

If you need products details information, please contact us.
Product Specifications
Bushing
SH
Weight
1.00Lbs
Material
Steel
Bore
finished
A
0.438"
B
1.871"
D
2.688"
E
0.875"
F
0.75"
G
0.125"
L
1.125"
Keyway
YES
SetScrews
1/4"-20
CapScrews
3-1/4X1-3/8
Installation
1. Be sure the tapered cone surfaces of the busing and the inside of the sprocket hub are clean.
2. Place bushing in sprocket, sheave, pulley or other QD parts.?
3. Place cap screws and lock washers loosely in pulling holes. ?Bushing remains fully expanded to assure sliding fit on shaft.
4. With key on shaft, slide sprocket to desired position on shaft. Be sure heads of cap screws are on outside.
5. Align sprocket. Tighten screws alternately and progressively-until they are pulled up tight. To increase leverage, use wrench or length of pipe. Do not allow sprocket to be drawn in contact with flange of bushing; there should be a gap from 1/8” to 1/4”

Caution:
When mounting screws, apply pressure by hand only. If extreme tightening forces are applied, bursting pressures will be created in the sprocket hub. There should be a gap of 1/8” to 1/4” between the face of the sprocket hub and the flange of the QD bushing. The gap must not be closed. If the gap is closed under normal tightening, the shaft is seriously undersized.

Remove
Removal
1. Loosen and remove cap screws
2. Insert cap screws in tapped removal holes;
3. Tighten inserted screws until sprocket is loose on shaft;
4. Remove sprocket from shfat

Contact Information

Contact: Jimmy

Mail: [email protected]/[email protected]

what app:+86 13588027172

Mobil: +86 13588027172

wechat:zjsprocket

Facebook: [email protected]

Please send your message to us
*Email
Tel
*Title
*Content

Agree to use terms of service

Contact Person
leave a message:
Contact Now
Address:
108# Dukou Road Hangzhou Zhejiang Province P.R China
Mobile Web
subscription
七星彩走势图体彩网 招商证劵智远理财平台 广西11选5app 青海十一选五前3直 湖北快三走势图分布图1000期 最好独平一码高手论坛 正规网上股票配资平台 广东快乐十分稳赢200 山东扑克3实时走势图 炒股如何开户去哪里开户 安徽省福彩快3走势图