Home > Products > Bushings > QD Bushings >

Martin Catalog QD Bushing SF

Martin Catalog QD Bushing SF

Martin Catalog QD Bushing SF
Martin Catalog QD Bushing SFMartin Catalog QD Bushing SF
CategoriesQD Bushings
AlbumView larger image
ModelSF
MaterialSteel C45
CatalogMartin Catalogue
Bore typestandard
SurfaceBlackoxided
Unit PriceUS $ 6.99 / piece
FOB portShanghai Port
Terms of PaymentL/C, Western Union
Update Time2019-12-29
Detail Information
Martin Catalog QD Bushing SF?
QD Bushing SF?
The taper-bored “QD” sprocket easily fits over the tapered hub and tightening of the cap screws produces a tight press fit on the shaft. The sprocket part is easily removed from the hub by using the pull-up bolts as jack screws in the holes tapped in the rim of the sprocket.

Zhijiang Sprocket factory has been making all kinds of Martin Catalog QD Bushing and sprockets for American customers more than 20years, material including steel C1045, SUS304, Casting.

If you need products details information, please contact us.

Product Information
Bushing
SF?
Catalog
Martin
Material
Steel
Weight
3.00Lbs
A
9/16"
B
3.125"
D
4 5/8"
E
1 1/2"
F
1 1/4"
G
1/4"
L
2 1/16"
Bore
finished
Keyway
Yes
CapScrews
3/8"X2"
Installation
1. Be sure the tapered cone surfaces of the busing and the inside of the sprocket hub are clean.
2. Place bushing in sprocket, sheave, pulley or other QD parts.?
3. Place cap screws and lock washers loosely in pulling holes. ?Bushing remains fully expanded to assure sliding fit on shaft.
4. With key on shaft, slide sprocket to desired position on shaft. Be sure heads of cap screws are on outside.
5. Align sprocket. Tighten screws alternately and progressively-until they are pulled up tight. To increase leverage, use wrench or length of pipe. Do not allow sprocket to be drawn in contact with flange of bushing; there should be a gap from 1/8” to 1/4”

Caution:
When mounting screws, apply pressure by hand only. If extreme tightening forces are applied, bursting pressures will be created in the sprocket hub. There should be a gap of 1/8” to 1/4” between the face of the sprocket hub and the flange of the QD bushing. The gap must not be closed. If the gap is closed under normal tightening, the shaft is seriously undersized.

Remove
Removal
1. Loosen and remove cap screws
2. Insert cap screws in tapped removal holes;
3. Tighten inserted screws until sprocket is loose on shaft;
4. Remove sprocket from shfat

Contact Information

Contact: Jimmy

Mail: [email protected]/[email protected]

what app:+86 13588027172

Mobil: +86 13588027172

wechat:zjsprocket

Facebook: [email protected]

Please send your message to us
*Email
Tel
*Title
*Content

Agree to use terms of service

Contact Person
leave a message:
Contact Now
Address:
108# Dukou Road Hangzhou Zhejiang Province P.R China
Mobile Web
subscription
七星彩走势图体彩网 湖南幸运赛车 家庭理财规划方案 老公隐瞒炒股亏了260万 河北快三开奖结果查询今 35选7开奖结果查询中奖结果辽宁 四川快乐十二遗漏数据 刘伯温期期准中特选一码 河南快三豹子号预测 黑龙36选7 股票融资比例下调了